| |
PE1RRR > PACKET 23.04.23 07:55l 120 Lines 3323 Bytes #999 (0) @ WW
BID : 12408-PE1RRR
Read: GUEST
Subj: Re: Vintage Packet [tncemu]
Path: IW8PGT<I3XTY<I0OJJ<GB7CIP<GB7COW<KE0GB<W9GM<WA8RSA<N3HYM<IW2OHX<
EI2GYB<GB7BEX<PE1RRR
Sent: 230423/0554Z @:PE1RRR.#NBW.NLD.EURO #:12408 [Rijen] $:12408-PE1RRR
From: PE1RRR@PE1RRR.#NBW.NLD.EURO
To : PACKET@WW
R:230422/1840Z 78616@KE0GB.#SECO.CO.USA.NOAM LinBPQ6.0.23
Original to PACKET@WW
The tncemu is a remarkable project, thanks for sharing!
I managed to get it working into the rrrnet hub-
RRRNET:PE1RRR-5} Connected to PE1RRR
Welcome to PE1RRR's Personal PBBS
Happy if you Post Msg
CMD(F/K/M/R/W/B/H/?)>
?
Commands
W(rite) = Type W (callsign)<cr> to begin message entering.
Subject> = Header(max 32 characters) are entered after the prompt: "Subject>".
Ending the header with a carriage return <cr>.
Message> = Message are entered after the prompt: "Message>".
Ending each line with <cr>.
You terminate with either a <cr>.<cr> or <cr><ctl-Z><cr>
to the indicate end of your message.
B(ye) = Type B<cr> to DISCONNECT.
F(ile) = Type F<cr> to show the latest 10 messages.
M(ine) = Type M<cr> to show latest 10 messages (to or from you).
Subsequent F or M command will show next 10 active messages.
R(ead) = Type R n<cr> to show the number n message.
K(ill) = Type K n<cr> to delete the number n message (only to or from you).
H(elp)or ?= Type H<cr> or ?<cr> to display this.
CMD(F/K/M/R/W/B/H/?)>
Can it support other TNC ROMs that might use the Z80 like the KPC?
Just curious!
I had to change MYMCALL to the same as my main callsign for it to
get a connection from the node, without any special setup that is
as its an auto-map node so it was like logging in directly. Very
nice.
bpq@gigabox:~/git/tncemu $ ./tnc -t rrrnet.ehvairport.com -p 10093
Connecting with Target Host rrrnet.ehvairport.com at port 10093
Protocol: AX25
Starting Emulation "hk21rom.bin"...
day 1505270713
|A
V-TNC
Virtual Machine TNC
AX.25 Level 2 Version 2.0
Emulated Z80 Machine 32k Rom / RAM
Mini PBBS ver 1.10 ase
Checksum $A2
cmd:cmd:
--snip
From the node side:
RRRNET:PE1RRR-5} Connected to PE1RRR
Welcome to PE1RRR's Personal PBBS
Happy if you Post Msg
CMD(F/K/M/R/W/B/H/?)>
?
Commands
W(rite) = Type W (callsign)<cr> to begin message entering.
Subject> = Header(max 32 characters) are entered after the prompt: "Subject>".
Ending the header with a carriage return <cr>.
Message> = Message are entered after the prompt: "Message>".
Ending each line with <cr>.
You terminate with either a <cr>.<cr> or <cr><ctl-Z><cr>
to the indicate end of your message.
B(ye) = Type B<cr> to DISCONNECT.
F(ile) = Type F<cr> to show the latest 10 messages.
M(ine) = Type M<cr> to show latest 10 messages (to or from you).
Subsequent F or M command will show next 10 active messages.
R(ead) = Type R n<cr> to show the number n message.
K(ill) = Type K n<cr> to delete the number n message (only to or from you).
H(elp)or ?= Type H<cr> or ?<cr> to display this.
CMD(F/K/M/R/W/B/H/?)>
Cool!
73
Red
Path: !W0ARP!KE0GB!
I have restored a lot of older TNC's. A lot of the TNC2 models
and some others. I also had a heathkit Pocket Packet and I decided
to create a virtual tnc that runs under linux and emulates the
processor and code in it. Works pretty well with direwolf as well
as ax.25. Can connect to kiss connections as well.
Project is on github... https://github.com/pfiliberti/tncemu
73
Read previous mail | Read next mail
| |
