| |
PA2SNK > JNOS 29.04.18 23:28l 263 Lines 6880 Bytes #999 (0) @ NLDNET
BID : 4303_PA2SNK
Read: GUEST
Subj: Mijn autoexec.nos
Path: IW8PGT<CX2SA<EA2RCF<LU9DCE<LU4ECL<VE2PKT<PI8CDR<PI8SNK
Sent: 180429/2100Z 63255@PI8SNK.#FRL.NLD.EURO [SNEEK/SNITS] FBB7.01.35 alpha
From: PA2SNK@PI8SNK.#FRL.NLD.EURO
To : JNOS@NLDNET
# Generated by: TstHWin v2.21b - Registered to PA2SNK
# On : 29-4-2018 22:45:22
# UTC: 29-4-2018 20:45:22
Tijd terug Jnos werkend gehad op xp middels bpq1632 gekoppeld aan bpq32.
doe er uw voordeel mee.
#
# autoexec.nos file created by zl3ai's INSTALL program version 961108.
#
hostname pd0snk.ampr.org
ax25 mycall pd0snk-1 # needs <Enter> to kickstart bbs
ax25 bbscall pd0snk # starts up immediately
ip address [27.137.86.1]
#
isat on
strace 0
#
# ======== AX.25 ========
ax25 maxframe 2
ax25 maxwait 15000
ax25 blimit 3
ax25 retr 15
ax25 timertype linear
#
# ======== TCP/IP ========
ip hsize 10
ip ttl 25
tcp irtt 10000
tcp maxwait 30000
tcp mss 216
tcp window 432
tcp retr 100
tcp timertype linear
# ======== Hardware interface(s) ========
# The syntax is:
# attach <hw type> <I/O address> <vector> <mode> <label> <bufsize>
# <mtu> [<speed>]
;attach packet 0x60 eth0 1500
attach bpq init 0x7f 60
;attach axip axip1 256 27.137.85.12 nl9sbg
attach bpq 1 bpq
attach bpq 4 loop
#
# Put TNC in KISS mode
#
# ======== AX.25 Parameters ========
# 1=TXD(10ms), 2=Persist, 3=Slotime, 4=TxTail, 5=FullDuplex
#
param bpq 1 40 # TX delay (x10mS)
param bpq 2 63 # Persistance (0-255)
param bpq 3 10 # Slot time (x10mS)
param bpq 4 10 # TX tail (x10mS)
param bpq 5 00 # 0 = HalfDuplex
# Port description for BBS (P)orts command.
ifconfig bpq descr "bpq32 port."
ax25 digipeat bpq off
#
# ======== NET/ROM ========
attach netrom
netrom alias SNKTCP
netrom call pd0snk
# netrom interface <iface> <quality> [<min-bc-quality>] [n]
# if <min-bc-quality> = 0, then only your own node is broadcast
netrom interface bpq 150 0
ifconfig netrom tcp blimit 3
ifconfig netrom tcp irtt 300000
ifconfig netrom tcp maxwait 900000
ifconfig netrom tcp mss 196
ifconfig netrom tcp retries 10
ifconfig netrom tcp timertype linear
ifconfig netrom tcp window 784
#
netrom nodefilter mode none
netrom acktime 2000
netrom choketime 60000
netrom derate on
netrom hidden off
netrom irtt 20000
netrom minquality 200
netrom nodetimer 1800
netrom obsotimer 1000
netrom promiscuous on
netrom qlimit 2048
netrom retries 15
netrom timertype linear
netrom ttl 18
#
# ======== SMTP ========
smtp usemx on
#SMTP setup
#don't beep for incoming mail!
smtp quiet yes
#route mail ourself
smtp mode route
#try to send batches to a host
smtp batch on
#time out mail delivery after 5 minutes
smtp t4 300
#kick any mail that might be in our spool from external mail and such
smtp kick
#
smtp gateway 27.137.86.1
# ======== FTP ========
ftptdisc 1200
ftpmax 2
#
# ======== Domain ========
domain suffix cbpr.org.
domain dns on
#
# ======== POP ========
#popmail addserver <popserver, e.g. zl3rr> 7200 pop3 nl4sne nl4sne nl4sne
#
# ======== Start processes ========
start ax25
start finger
start forward
start ftp
start netrom
start smtp
start telnet
start ttylink
start pop3
start smtp
#
# ======== Mail Box ========
# Use 'mbox attend off' and 'attended off' at unattended sites.
# This prevents 'ttylink' or mbox 'O' sessions from clogging things up.
mbox fbb on
mbox attend on
attended on
mbox haddress pd0snk.pi8snk.#frl.nld.eu
mbox mport bpq on
mbox mailfor watch pd0snk
# exclude the following from the mailfor broadcast
#mbox mailfor exclude nl4sne
# mail-for broadcast interval
mbox mailfor 900
mbox newmail on
mbox fwdinfo "TCPIP JNOS v1.11f"
mbox qth "Sneek, Frl"
mbox zipcode 8608aw
mbox header on
# Geen smtp headers bij ax25 forwarding : mbox smtptoo off (default)
mbox smtptoo on
# set mail-for beacon path if desired
#ax25 route add MAIL bpq cb8snk
# "Accept (Y/N)" after entering message
mbox sendquery off
# inactivity timeout in seconds
mbox tdisc 600
# forwarding interval, when = 0, stops forwarding
mbox timer 3600
mbox tmsg "(Please use your callsign to log in)"
# Set some mbox aliases - these ones aid remote problem diagnosis ;-)
# (NOTE- the "@" prefix for aliases was introduced in JNOS 1.11X1)
mbox alias smtp "@smtp list"
mbox alias ifc @ifc
mbox alias axr "@ax25 route"
mbox alias arp @arp
#
# ======== Function keys ========
# f1-59 | sf1-84 | cf1-94 | af1-104 | pgup-73
# f2-60 | sf2-85 | cf2-95 | af2-105 | pgdn-81
# f3-61 | sf3-86 | cf3-96 | af3-106 | home-71
# f4-62 | sf4-87 | cf4-97 | af4-107 | end -79
# f5-63 | sf5-88 | cf5-98 | af5-108 | arup-72
# f6-64 | sf6-89 | cf6-99 | af6-109 | ardn-80
# f7-65 | sf6-90 | cf7-100 | af7-110 | ar l-75
# f8-66 | sf8-91 | cf8-101 | af8-111 | ar r-77
# f9-67 | sf9-92 | cf9-102 | af9-112 | ins -82
# | sf10-93 | cf10-103 | af10-113 | del -83
# f11-133 | sf11-135 | cf11-137 | af11-139 |
# f12-134 | sf12-136 | cf12-138 | af12-140 |
#
# (the "~" forces it into the command session)
#
# F1 to F4 select sessions 1 to 4
fkey 59 "~S 1^M"
fkey 60 "~S 2^M"
fkey 61 "~S 3^M"
fkey 62 "~S 4^M"
#
# F5 records current session, F6 uploads file to current session.
fkey 63 "~record "
fkey 64 "~upload "
#
# fkey 65 (F7) is to access your own bbs
fkey 65 "~bbs^M"
# fkey 66 (F8) sends your callsign twice for login & password to access bbs
fkey 66 "nl4sne^Mnl4sne^M"
#
# fkey 75 (Left arrow) is changed to Backspace...to minimise frustration ;-)
fkey 75 "^H"
#
# SF1 to SF4 change sessions 1 to 4 to split mode
fkey 84 "~session 1 split on^M"
fkey 85 "~session 2 split on^M"
fkey 86 "~session 3 split on^M"
fkey 87 "~session 4 split on^M"
#
# SF5 to SF8 change tracing
fkey 88 "~trace bpq off^M"
fkey 89 "~trace bpq 0111^M"
#
fkey 90 "~trace bpq 0211^M"
fkey 91 "~trace bpq 0311^M"
#
# Alt-F10 displays the last entries in todays log.
fkey 113 "~taillog^M"
#
# F12 to exit JNOS.
fkey 134 "~exit^M"
#
# ======== Routing ========
route add default bpq
# Load routing information contained in ROUTING.SCR file.
source routing.scr
#
netrom load
at now+0001 "netrom bcnodes bpq"
at now+0002 "netrom bcnodes bpq"
;at now+0001 "netrom bcnodes axip"
;at now+0002 "netrom bcnodes axip"
#
trace bpq 0111
#
# ======== Beacon ========
# set ID beacon path if desired
#ax25 route add ID bpq <digipeater>
ax25 bcinterval 3600
# [locator] in bctext can be read by APRS systems, e.g. [RE66jw].
ifconfig bpq ax25 bctext "[JO23ta] JNOS started"
ax25 bc bpq
ifconfig bpq ax25 bctext "[JO23ta] JNOS"
;ifconfig axip ax25 bctext "[JO23ta] JNOS started"
;ax25 bc axip
;ifconfig axip ax25 bctext "[JO23ta] JNOS"
#
# THE END
#
о о
о о
ооо ооо
оооо оооо
оооооо оооооо
оо ооооо оо
о ооо о
ооооооо ооооооо
оооооооо оооооооо
PA2SNK te Sneek/Snits (Friesland)
Read previous mail | Read next mail
| |
