OpenBCM V1.07b12 (Linux)

Packet Radio Mailbox

IW8PGT

[Mendicino(CS)-Italy]

 Login: GUEST





  
G8MNY  > TECH     19.05.22 10:23l 55 Lines 2175 Bytes #999 (0) @ WW
BID : 22047_GB7CIP
Read: GUEST
Subj: 70cm Collinear
Path: IW8PGT<IZ3LSV<DB0ERF<OK0NAG<OK0NBR<SR1BSZ<IW0QNL<VE2PKT<W0ARP<CX2SA<
      VK7AX<GB7CIP
Sent: 220519/0912Z @:GB7CIP.#32.GBR.EURO #:22047 [Caterham Surrey GBR]
From: G8MNY@GB7CIP.#32.GBR.EURO
To  : TECH@WW

(8 Bit ASCII graphics use code page 437 or 850, Terminal Font)
Stacked 5/8 Wave Co-linear For 430-440 MHz         (Comment added Nov 05)

                                   ±±±
                          Element->±±±
                                   ±±±
 ÄÄÄÄÄÄÄÄ>¿Ú<Ä-Braid               ÅÅ<ÄÄÄ¿
    7mm__ÛÛ³                      ±±±    
 ³       ±±±±             Element->±±±  Shirt Buttons
 ³       ±±±±  5/8 wave            ±±±    
 ³       ±±±±                      ÅÅ<ÄÄÄÄÙ
 ³       ±UR±  E                   ±±±
241mm    ±±±±  L          Element->±±±
 ³       ±43±  E                   ±±±
 ³       ±±±±  M      <---162mm--->ÚÁ¿<--"N" Socket
 ³       ±±±±  E      ÍÍÍÍÍÍÍÍÍÍÍÍÍ´ ÃÍÍÍÍÍÍÍÍÍÍÍÍÍ
 ³    ___±±±±  N      Ground Plane ÀÄÙ Ground Plane
    7mm ³ÛÛ   T
 ÄÄÄÄÄÄÄ>ÙÀÙ

The Elements are made from UR43 or RG58\U (not RG58\CU) coax. You MUST use 50
ohm coax with a solid copper centre.

Use plastic or fibre glass as a tube cover for the elements but do not use grey
tube as this could have a carbon conductive content.

There are four 5mm dia ground planes that must have a contact with the outer
body of the "N" connector socket.

You can "Stack" as many elements as you wish within reason, trim 10mm off the
last element then check V.S.W.R. Repeat until resonance is achieved. Place the
tube cover over the elements w checking V.S.W.R. You should be able to reach a
good resonance around 1 to 1.

Use the holes in the shirt buttons as an isolator between the element solder
connections, the elements are connected inner/outer, outer/inner at each end of
the element "Crisscrossing" to the next, once completed use some strong fishing
nylon line around the last element to pull all the elements straight then fix
the line over the top of the tube with a waterproof cap.

73 de Alan 2E1ESY  @GB7NND.#23.GBR.EU
------------------------------------------------------------------------------

Here on HR1BY I tried this one, it works wonderfull, a repeater, i could not
acces before, I now do it with even less power.
73 - WOLF, HR1BY @ HR1PAQ


Why Don't U send an interesting bul?

73 De John, G8MNY @ GB7CIP


Read previous mail | Read next mail


 23.12.2024 17:55:17lGo back Go up