OpenBCM V1.07b12 (Linux)

Packet Radio Mailbox

IW8PGT

[Mendicino(CS)-Italy]

 Login: GUEST





  
G8MNY  > TECHNI   22.12.19 10:43l 272 Lines 12638 Bytes #999 (0) @ WW
BID : 36689_GB7CIP
Read: GUEST
Subj: A Quality Crystal Set
Path: IW8PGT<CX2SA<OK2PEN<GB7CIP
Sent: 191222/0937Z @:GB7CIP.#32.GBR.EURO #:36689 [Caterham Surrey GBR]
From: G8MNY@GB7CIP.#32.GBR.EURO
To  : TECH@WW

By G8MNY                                  (Correction Apr 17)
(8 Bit ASCII graphics use code page 437 or 850, Terminal Font)

Here is my design using fairly modern parts. With it I came 1st in my local
radio club home constructions contest a few years ago, mainly because it was so
LOUD.

It gives VERY good sensitivity & selectivity. With 10mV RMS carrier @ 1MHz
modulated 100% @ 1kHz on the low Z aerial input, gave at best match 5mV RMS
into the 80ê headphones. In the high Z mode, 10mV gave 1.5mV to the headphones,
but the input circuit is untuned (no gain) & is just tightly transformer
coupled. The selectivity was measured at 1MHz for -3dB was ñ25kHz & at -20dB
ñ190kHz or a loaded Q of 20.

In South London with 40M of aerial wire up @ 8M it can pick up 7 MW & 4 LW
stations (3 French) during the day. The stronger ones can even just about drive
a good small 8ê LS.

SCHEAMAIC
=========
          ÚÄÄÄÄÄÄÄ¿        ÚÄÄÄÄÄÄÄÄ¿ÚÄÄÄÄÄÄÄÄ¿ÚÄÄÄÄÄÄ¿ÚÄÄÄÄÄÄÄÄÄ¿   _
\³/       ³Aerial ³Variable³Detector³³Crystal ³³RF /  ³³Impedance³  / \
 ³_/ÄHighZ´Tunned ³Magnetic³Tunned  ôDetectorôAudio ômatching ÃÄ() ()
    ÄLow Z´Circuit³Coupling³Circuit ³³        ³³Filter³³& DC Path³ Efficient
 ÚÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÙ        ÀÄÄÄÄÄÄÄÄÙÀÄÄÄÄÄÄÄÄÙÀÄÄÄÄÄÄÙÀÄÄÄÄÄÄÄÄÄÙHeadphones
_³_
///

FEATURES
========
1/ DUAL TUNED CIRCUITS for Selectivity.
2/ VARIABLE COUPLING for Matching/Sensitivity/Selectivity.
3/ VARIABLE INDUCTANCE also widens the tuning range.
4/ DUAL BAND, MW & LW, plug in capacitors extend range to LW.
5/ HIGH & LOW AERIAL IMPEDANCE option, for best matching for short & long ant.
6/ AERIAL NEON gives visible protection against High Aerial Voltages.
7/ LENS to see "CAT's WHISKER on the CRYSTAL".
8/ R.F.C. to improve diode linearity & sensitivity performance (RF/AF Filter).
9/ TAPPED AUDIO MATCHING TRANSFORMER for optimum loudness.
10/ HIGH EFFICIENCY HEADPHONES home made.

CIRCUIT
=======           GERMANIUM
     AUDIO AUTO     CRYSTAL             ADJUSTABLE                AERIAL &
     MATCHING       VIEW __  DETECTOR  FERRITE ROD   AERIAL        EARTH
    TRANSFORMER     LENS<__>    COIL    <COUPLING>    COIL      CONNECTIONS
                               = = = = = = = = = = = = = = =
SENSITIVE ÚÄÄÄÄÂÄÄ((()ÄÄÄ´<³ÄÄÂÄ((((()Ä¿          ÚÄ((((()Ä¿
HEAD-   7_³    ³  ====        ³        ³          ³        ³        HIGH
PHONES  6_)º   ³  RFC       _ ÃÄÄÄ¿    ³        _ ÃÄÄÄÂÄÄÄÄ)ÄÄÄÄÄÄO Z
@-\     5_)º   ³           |\ ³   ³    ³       |\ ³   ³    ³
   ³    4_)º   ³    2x 300pF ===   /LW ³ 2x 300pF===   /LW ³      LOW Z
@Ä/.....3_)º   ³     variable ³\  ³    ³  variable³\  ³    ÃÄÄÄÄÄÄO
³   TAP 2_)º   ³              ³   ³    ³          ³   ³   (:)     / Earth for
³       1_)º  ===             ³  ===   ³          ³  ===   ³NEON ³  High Z
³       )_)º   ³ 10nF RF      ³   ³1n5 ³          ³   ³1n5 ³     ³
³        ³     ³ decoupling   ³   ³    ³          ³   ³    ³     ³
ÀÄÄÄÄÄÄÄÄÁÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÁÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÁÄÄÄÁÄÄÄÄÁÄÄÄÄÄÁÄO EARTH

PARTS & TIPS
============
THE BASE
Use a wooden base board about 1x 25 x 10cm. Fit rubber feet so that underside
protrusions don't scratch.

CIRCUIT WIRING
Use tin plate strips tacked down, this is easy to solder to & support the
smaller components.

HEADPHONES
Use a coat hanger wire head band to connect 2x 40ê 1970s telephone inserts
(type 4T) rocking armature type. These are the most sensitive transducers made
& peak @ 3kHz. They are around 10dB louder once matched than any high Z moving
iron diaphram, moving coil, or crystal types.
                                                     _..--~~~~--.._
Make a headband from a single piece of             /    Headband    \
coat hanger wire looped at each end &             |                  |
flattened (hammered) as the common             __³__               ___³__
connection under 2 of the terminal nuts.     _/     \             /(o)(o)\
Bend the wire to angle the inserts to       ³|  .'.  |           ³ ³~~~~~~|
sit on your ears comfortably. They can       \\_____/             \_\____/
be connected permanently to the set with           '.               .'
flexible leads or with a plug & socket               '.    wires  .'
for comparing with other headphones.                   '.       .'
Wind a couple of turns of the insulated                    80ê
wire around the headband as strain releif.

AF TRANSFORMER
Acts as a large AF inductive load to the               _____
detector's DC, maintaining conduction              ___³     ³___
over > 50% of the RF cycle! For best load         /o _³__   ³   \ 0V
matching & volume, I used 6 equal winding      4 ³,_' ³  |  ³ ,('³
of an old telecomms line transformer that      5 ³,_' ³  |  ³(,_'³1
had 2x 600ê windings in 4 sections each.       6 ³,_' ³  |  ³ ,_'³2
The first 2 windings are paralleled up         7 ³, ' ³  |__³_, '³3
for low Z loads to reduce the winding             \___³     ³__o/
resistance loss for low Z loads.                      ÀÄÄÄÄÄÙ

Adjustable connection is made with a small wander crocodile clip to the linking
straps. Typically 2-3 of the 7 taps gives the best for the 80ê headphones.
Mount it well to the base board (e.g. 2 screws tapped into the 4 plastic
corners not near the winding!) as it is heavy component.

If a suitable comms transformer is not available
try some small mains transformers that can give     ÄÄÄÂÄÄÄÄ¿
7:1-2:1 e.g. 110V to 15-0-15V, try fine ratio      15V  )||(
adjustment by 1st using it as a straight             ___)||(110V
transformer then as an auto transformer with the    0V  )||(
windings in series, & try adding or subtracting    15V  )||(___
the secondary (reverse connections) to alter the       ³
ratio & use which ever gives the loudest volume.    ÄÄÄÁÄÄÄÄÄÄÄ
Also try paralleling or seriesing up the headphone
earpieces to change the load.

10nF CAPACITOR
This is used for blocking RF from the AF circuit. Theory says yes it is needed,
but it is not really necessary component as it works without it.

R.F. Choke
Approx 20 turns of enamelled copper wire (0.5mm) on small polo mint sized (12mm
dia) toroidal RF ferrite core. Again theory says yes it is needed as it will
keep the diode conduction angle high & hence reduce the diode resistive losses,
but it does work without it. It will also makes the load impedance on the tuned
circuit 2x higher, as mean not peak voltage & currents are reduced by û2. Mount
with an insulated screw (not to cut into the turns) through the middle.

GERMANIUM DIODE
Viewable old large glass bubble type e.g. an old OA91.

Mount a small plastic lens (from              ,_______.
cardboard slide viewer) 2cm in               // _     \\ OA91
front of the crystal with shaped          =====³_³~\.=======
paper clip wire, so that the surface         \\_______//
of the crystal & the internal                 ~~~~~~~~~
cat's whisker can clearly be seen.

GANGED 300pF VARIABLES
Two needed, air spaced ideally. Large value gives best tuning range, so the
sections are paralleled up. Put knobs on the shafts & mount them well to the
baseboard, as they get a lot of tweaking.

1n5 LW CAP
Two needed. Connected one side to ground & the other to a 2mm wander test
plugs/sockets to give the Long Wave coverage.

FERRITE ROD
Standard radio type 14cm long, 8mm dia, but not used as the aerial! It gives
plenty of L adjustment & coupling variation. With the coils the ferrite gives
high Q tuned circuits, many times higher than lit's wire air space coils!
Mount with plastic cable clip in the middle (not shorting metal turn!) with
high enough packing/washers to allow coils to be moved. The ferrite rod is
quite fragile, if it does get broken just glue it back together with a 2 part
epoxy resin, removing as much glue gap with presure while setting as possible.

COILS
Two standard MW radio type with tags,    ÚÄÂÂÂÂÂÂÂÂÂÂÂÂÂ[]Ä¿Paper
e.g. about 30 turns of 0.5mm enamelled   ³ ||||||||||||| \ ³tube
copper wire on a loose fitting paper     ÀÄÁÁÁÁÁÁÁÁÁÁÁÁÁ[]³Ù
tube with connection tags.               30 turns   Tags  \³____Twisted
                                                            ~~~~Flex Wire
Connect with twisted flexible leads as they will need sliding along the ferrite
rod to vary the inductances & coupling.

NEON
Wire ended 80V bulb type. Used for safety, it gives a dramatic flash discharge
indication when the aerial is in the low Z mode, when static is around. It also
protects the Caps from much higher voltage flashovers!

CONNECTIONS
4mm socket with screw up type for Earth & the 2 Aerial options, with a swinging
earth link plate, to make the high Z aerial configuration. For the headphone, I
used 6mm (¬") Jacks, but screw up 4mm are fine also.

LAYOUT
======          wooden base with feet
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³            Ferrite°°°°±±±±±±°°°°°Û°°°°°±±±±±±°°°°° ³
³               rod     coil       ßclip  coil       ³
³       AF                _LW Cap_    _LW Cap_       ³
³  Transformer           /________   /________    (o)³AE High Z
³    ³~~°°~~³ RFC  Diode ³ðððððððð³  ³ðððððððð³      ³
³____³::°°::³  ,-.   __  ³ðððððððð³  ³ðððððððð³   (o)³AE Low Z
³ LS ³::°°::³ ( 0 )-(__)-³ðððððððð³  ³ðððððððð³   ³ ³³Earth Link
³Jack³__°°__³ÞC`-'  ____ ³________³  ³________³[] (o)³Earth
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ<____>ÄÄÄij³ÄÄÄÄÄÄÄÄÄij³ÄÄÄÄÄÄÄÄÄÄÙ
crock clip tap     lens    KNOB        KNOB   neon

TUNING IN
=========
1/ Connect an earth, mains earth can be noisy, old Gas & Water pipes are better
   earths as long as they are not PLASTIC! Try a counterpoise along the ground
   if there is too much mains QRM on water pipes etc.
 
2/ Connect the aerial to either the High Z or Low Z options. Short aerial wires
   compared to a 1/8 wave length are always high Z. Higher & longer aerial
   wires are always better, as they pick up more RF power.

3/ With the coils close together, adjust the detector & aerial variable
   capacitors for a station of interest.

4/ If the station is loud enough, but can't be separated from another one try
   adjustment of the 2 variable capacitors at once, also reduce the coupling by
   moving the coils apart & try again. Note the affect of tracking both
   variables, there is a best matching sweet spot for optimum loudness.

5/ Adjust the auto-transformer tapping for loudest output, note that there is
   some treble difference as the match changes the Z on the RF decoupling Cap.

6/ Try the other aerial impedance option & see if other stations are heard.

7/ If the station is too HF or LF for the tuning range, try moving the coils
   more to the middle for LF, or to the far ends for HF.

8/ With the LW capacitors connected the tuning is less effective & moving the
   coils gives more frequency range.

DEMONSTRAITON
a) Scope & Spectrum analyse (hi Z probes) the aerial with xtal set in // tuned
   input to show the broadband RF signals.
   ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
   ³     SCOPE RF     ³ ³     SPECTRUM     ³
   ³± ±±± ± ±± ±±± ±± ³ ³                  ³
   ³±±±±±±±±±±±±±±±±±±³ ³   ³     ³     ³  ³
   ³±±±±±±±±±±±±±±±±±±³ ³ ³ |  | ³|  ³  |  ³
   ³±±±±±±±±±±±±±±±±±±³ ³ | ݳ Ý |ݳ |³ Ý  ³
   ³ ± ±±±±± ±± ±±± ±±³ ³ ݳÝ|ÞÝ ÝÝ| Ý| ݳ ³
   ³                  ³ ³~~~~~~~~~~~~~~~~~~³
   ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

b) Connect an AF amplifier & LS right across the full transformer, & move the
   scope & analyser to the 2nd tuned circuit & tune across the band.
   ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
   ³     TUNNED LF    ³ ³    TUNNED HF     ³
   ³   ³              ³ ³               ³  ³
   ³   |              ³ ³            ³  |  ³
   ³ ³ ݳ |  ³        ³ ³   ³     |  |³ |  ³
   ³ |³Ý| Ý ||  ³  ³  ³ ³   |  | |ݳ Ý| ݳ ³
   ³ Ý|ÛÞÞÝ Ýݳ |³ | .³ ³ ³.ݳ Ý ÝÝ| ÛÞ Ý| ³
   ³~~~~~~~~~~~~~~~~~~³ ³~~~~~~~~~~~~~~~~~~³
   ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

c) Tune into a strong station.
   ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
   ³    SCOPE RF      ³ ³     SPECTRUM     ³
   ³±  ±    ±   ±   ± ³ ³      .           ³
   ³± ±±±   ±± ±±   ±±³ ³      |           ³
   ³±±±±±±-±±±±±±±-±±±³ ³   ³  | .         ³
   ³± ±±±   ±± ±±   ±±³ ³ ³ |  Ý |³³ ³  ³  ³
   ³±  ±    ±   ±   ± ³ ³ |.ݳÞÛ Ý|| || |. ³
   ³                  ³ ³~~~~~~~~~~~~~~~~~~³
   ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

d) Scope the recovered AF on the transformer.
   ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
   ³    SCOPE AF      ³
   ³                  ³
   ³Ä¿ Ú¿   Ú¿  Ú¿  Ú¿³
   ³ ³ÚÙÀ¿  ³À¿ÚÙ³  ³À³
   ³ ÀÙ  À¿ÚÙ ÀÙ À¿ÚÙ ³
   ³      ~~      ~~  ³
   ³                  ³
   ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

See my TECH bul on "Spectrum IF Demo circuit"

Why don't U send an interesting bul?

73 de John G8MNY @ GB7CIP


Read previous mail | Read next mail


 24.12.2024 14:40:19lGo back Go up