| |
CX2SA > SATDIG 11.06.18 16:52l 841 Lines 23902 Bytes #999 (0) @ WW
BID : AMSATBB13203
Read: GUEST
Subj: AMSAT-BB-digest V13 203
Path: IW8PGT<IR2UBX<SR1BSZ<SV1CMG<ON0AR<OZ5BBS<CX2SA
Sent: 180611/1430Z @:CX2SA.SAL.URY.SOAM #:45742 [Salto] FBB7.00e $:AMSATBB13203
From: CX2SA@CX2SA.SAL.URY.SOAM
To : SATDIG@WW
Today's Topics:
1. AMSAT Joe Talks Cubesats (Randy Hall)
2. AO-73/FUNcube Mode change (Jim Heck)
3. Rotor control with SatPC32ISS (Stephan Greene)
4. Re: AO-92 is in L/v as of 0143Z 10Jun (Greg D)
5. Re: AO-92 is in L/v as of 0143Z 10Jun (Andrew Glasbrenner)
6. Re: VUCC Awards-Endorsements for May 2018 (R.T.Liddy)
7. Junior Woodchucks guide to AO-91 (Wendy and Terry Osborne)
8. Re: DSLWP Successful Configurations and Subsequent UHF Test
Plan (Jean Marc Mompl?)
9. Re: Rotor control with SatPC32ISS (Mark L. Hammond)
10. Re: IC-9100 and SATPC tracking help needed (Kirk P)
11. Re: IC-9100 USB driver issues with WIN10 PRO ver 1803
(jeff griffin)
----------------------------------------------------------------------
Message: 1
Date: Sun, 10 Jun 2018 09:48:42 -0700
From: Randy Hall <listk7age@?????.???>
To: AMSAT BB <AMSAT-BB@?????.???>
Subject: [amsat-bb] AMSAT Joe Talks Cubesats
Message-ID:
<CAPCSVhqASk05Q=UZ9-PgoragLBFpme8OUcm8mNM+94gHV7v5hw@????.?????.???>
Content-Type: text/plain; charset="UTF-8"
Joe Spier K6WAO AMSAT President talks about cubesats on the beach at the
SEA-PAC hamfest.
He also tried to make a contact through a satellite but didn't have
success. No video of that.
K7AGE Video <https://youtu.be/Gl_RpYcNlGU>
73
Randy, K7AGE
------------------------------
Message: 2
Date: Sun, 10 Jun 2018 18:17:19 +0100
From: "Jim Heck" <jim@??????.??.???>
To: <amsat-bb@?????.???>
Subject: [amsat-bb] AO-73/FUNcube Mode change
Message-ID: <3E8697497CF6461BA33C05D9B7EBED37@??????>
Content-Type: text/plain; charset="UTF-8"
Hi folks,
I have just changed the sat into education mode (full power beacon in
sunlight, low power beacon plus transponder on in darkness).
I will be switching mode as normal to full time transponder mode on sometime
on next Fri pm UTC .
73s Jim G3WGM and the FUNcube team.
------------------------------
Message: 3
Date: Sun, 10 Jun 2018 14:15:48 -0400
From: Stephan Greene <ks1g04@?????.???>
To: Amsat-bb <amsat-bb@?????.???>
Subject: [amsat-bb] Rotor control with SatPC32ISS
Message-ID:
<CACZz0S1G6Afmv5ChESWy9wb7ibFXMZEvCYgsasy9eShWW0_UuQ@????.?????.???>
Content-Type: text/plain; charset="UTF-8"
Long-time SatPC32 user but new to SatPC32ISS. Rig control works fine, but
I can't get rotor control working in SatPC32ISS. Guessing that SatPC32ISS
is not launching the rotor control server SatPC32 uses. Suggestions? Does
SatPC32ISS default to the same config file as SatPC32, or does it default
to Confguration 1? (I'm using Config II with SatPC32). Have not found
anything (yet) in the SatPC32 docs.
Thanks, 73 Steve KS1G
------------------------------
Message: 4
Date: Sun, 10 Jun 2018 11:51:11 -0700
From: Greg D <ko6th.greg@?????.???>
To: Andrew Glasbrenner <glasbrenner@??????????.???>,
amsat-bb@?????.???
Subject: Re: [amsat-bb] AO-92 is in L/v as of 0143Z 10Jun
Message-ID: <ca1fb616-1149-e89d-1fd0-0a7dc4d47287@?????.???>
Content-Type: text/plain; charset=us-ascii
Hi Drew,
Are the plans to follow this schedule for the Field Day weekend?
Greg KO6TH
Andrew Glasbrenner wrote:
>
>
> .subject says it all.
>
>
>
> 73, Drew KO4MA
>
>
>
> _______________________________________________
> Sent via AMSAT-BB@?????.???. AMSAT-NA makes this open forum available
> to all interested persons worldwide without requiring membership. Opinions
expressed
> are solely those of the author, and do not reflect the official views of
AMSAT-NA.
> Not an AMSAT-NA member? Join now to support the amateur satellite program!
> Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
------------------------------
Message: 5
Date: Sun, 10 Jun 2018 16:40:00 -0400
From: "Andrew Glasbrenner" <glasbrenner@??????????.???>
To: "'Greg D'" <ko6th.greg@?????.???>
Cc: amsat-bb@?????.???
Subject: Re: [amsat-bb] AO-92 is in L/v as of 0143Z 10Jun
Message-ID: <001f01d400fb$33b888f0$9b299ad0$@??????????.???>
Content-Type: text/plain; charset="us-ascii"
I'd like to run L for part of the weekend, but it will have to be the first
half. I can't commit to an exact time for the change, but will probably try
Friday evening. If you have L capability, this is the way to an easy 100
points.
73, Drew KO4MA
-----Original Message-----
From: Greg D <ko6th.greg@?????.???>
Sent: Sunday, June 10, 2018 2:51 PM
To: Andrew Glasbrenner <glasbrenner@??????????.???>; amsat-bb@?????.???
Subject: Re: [amsat-bb] AO-92 is in L/v as of 0143Z 10Jun
Hi Drew,
Are the plans to follow this schedule for the Field Day weekend?
Greg KO6TH
Andrew Glasbrenner wrote:
>
>
> .subject says it all.
>
>
>
> 73, Drew KO4MA
>
>
>
> _______________________________________________
> Sent via AMSAT-BB@?????.???. AMSAT-NA makes this open forum available
> to all interested persons worldwide without requiring membership.
> Opinions expressed are solely those of the author, and do not reflect the
official views of AMSAT-NA.
> Not an AMSAT-NA member? Join now to support the amateur satellite program!
> Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
------------------------------
Message: 6
Date: Mon, 11 Jun 2018 01:10:12 +0000 (UTC)
From: "R.T.Liddy" <k8bl@?????????.???>
To: "Ronald G. Parsons" <w5rkn@?????.???>, AMSAT-BB
<AMSAT-BB@?????.???>
Subject: Re: [amsat-bb] VUCC Awards-Endorsements for May 2018
Message-ID: <770066744.3256600.1528679412994@????.?????.???>
Content-Type: text/plain; charset=UTF-8
Ron,
Thanks for keeping this updated every month!
BTW, many of the FT8 folks are involved in the ARRL
Grid Chase and want to keep their monthly and cumulative
scores up to date as quickly as possible. That would be
why you see the LoTW QSLs coming in so fast.
73, Bob K8BL
________________________________
From: Ronald G. Parsons <w5rkn@?????.???>
To: AMSAT-BB <AMSAT-BB@?????.???>
Sent: Friday, June 1, 2018 11:51 AM
Subject: [amsat-bb] VUCC Awards-Endorsements for May 2018
Here are the endorsements and new VUCC Satellite
Awards issued by the ARRL for the period May 1, 2018
through Jun 1, 2018.
Congratulations to all those who made the list this month!
CALL 01 May 2018 01 Jun 2018
KO4MA 1598 1627
KD8CAO 1240 1253
N8HM 1025 1054
N8RO 1040 1051
K4FEG 877 901
K6FW 703 743
N9IP 589 609
N6UK 551 568
K5ND 502 526
WD9EWK 430 441
KE4AL 317 379
NS3L 300 325
VE7CEW 292 304
AA9LC New 299
AA8CH 218 256
G0ABI 124 200
N3GS 130 198
AA4FL 164 181
KE8FZT 100 175
XE1SEW New 130
WU2M New 105
KB2YSI New 101
PU8MRS New 100
If you find errors or omissions. please contact me off-list
at <mycall>@<??????>.com and I'll revise the announcement.
This list was developed by comparing the ARRL .pdf
listings for May 1, 2018 and June May 1, 2018. It's a visual
comparison so omissions are possible. Apologies if your
call was not mentioned. Thanks to all those who are
roving to grids that are rarely on the birds. They are
doing most of the work!
EDITORIAL: Excuse the bandwidth.
I took a little detour from chasing grids to try FT8 on 6 meters.
What amazed me was the quickness of QSLs on LoTW, often finding
the QSL awaiting when I uploaded my QSO. Why are the FT8-ers so
fast compared with my experience on satellites. My guess is that
FT8 QSOs are done with computer software with logging capability.
But that can't be the entire reason. Most of our wonderful rovers
are extremely fast getting their audio recording logs uploaded to
LoTW. So motivation has to be part of the solution.
Satellites can be worked without computer assistance, but Doppler
control, pass prediction and logging make the activity more
enjoyable for me. Some of the rovers should publish their
procedure for logging to LoTW. Most logging programs will upload
to LoTW. Even the TQSL program for LoTW handles hand-input
parameters. And LoTW is the easiest way to apply for ARRL Awards.
Perhaps my disappointment after working a needed grid and not
getting an LoTW QSL can be relieved.
73,
Ron W5RKN
_______________________________________________
Sent via AMSAT-BB@?????.???. AMSAT-NA makes this open forum available
to all interested persons worldwide without requiring membership. Opinions
expressed
are solely those of the author, and do not reflect the official views of
AMSAT-NA.
Not an AMSAT-NA member? Join now to support the amateur satellite program!
Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
------------------------------
Message: 7
Date: Mon, 11 Jun 2018 14:09:55 +1200
From: "Wendy and Terry Osborne" <wandtosborne@?????.???>
To: <amsat-bb@?????.???>
Subject: [amsat-bb] Junior Woodchucks guide to AO-91
Message-ID: <DCBEC7DD24EA4E35AE8DDA883EB48B44@??????????>
Content-Type: text/plain; charset="iso-8859-1"
Hi Folks,
Some time ago I wrote up a guide to AO-85 for my local club magazine.
I have now updated it for AO-91.
If it is of use to anyone, help yourself.
https://www.dropbox.com/s/r4re1rkr1ym8st2/Working%20the%20AO91%20Fox-1B%20FM%2
0Repeater.pdf?dl=0
73,
Terry Osborne ZL2BAC
AMSAT-NA Member 6849
------------------------------
Message: 8
Date: Mon, 11 Jun 2018 14:50:00 +0400
From: Jean Marc Mompl? <jean.marc.momple@?????.???>
To: ??? <wmc_jx@???.???>
Cc: "amsat-bb@?????.???? <amsat-bb@?????.???>
Subject: Re: [amsat-bb] DSLWP Successful Configurations and Subsequent
UHF Test Plan
Message-ID:
<CAMk2N4jqjD_98wbLbKGkrNRR=KR2wUiXZcvd+iuY-Omn=p4SJg@????.?????.???>
Content-Type: text/plain; charset="UTF-8"
Dear All,
Tested this morning during DSLWP (Longjiang 2) Tx between 06:00 and 08:00
UTC, no luck no signal received in spite everything OK and tested several
times yesterday. The set-up is RTL SDR (tried also with TS-2000), feeder:
30m of 1/2" heliax + 3m of RG213, DBA-270 preamp and Hy-gain UB-7030SAT
antenna, basically the same station I used for LEO's.
More or less expected, but was worth giving it a try, hopefully it will
work with JT4.
I will try again GMSK, particularly if there is a night transmission in
future (less noise).
First quick conclusion is that I need much more antenna gain for the GMSK
mode (some already mentioned that), need to figure out what mechanically
possible on my apartment roof to get maximum possible gain.
To those successful today congratulations.
73
Jean Marc (3B8DU)
On 10 June 2018 at 16:25, Jean Marc Momple <jean.marc.momple@?????.???>
wrote:
> Wei & all,
>
> Everything working this side, decoded the raw file and uploaded on the
> server successfully.
>
> Unfortunately could not take the opportunity of this morning transmission
> as a brand new preamplifier installed yesterday (tested OK) blew the fuse
> this morning and went SK. I replaced it today.
>
> So ready for tomorrow?s transmission and if ever possible to receive the
> sat with a 2 x 15 ele. circular polarized antenna, DBA-270 preamp + 30m of
> 1/2? heliax feeder, I should make it. If not will wait for JT-4
> transmission.
>
> Any idea what is the best Polarization RHCP or LHCP? would be useful to
> start with the best one. In any case, as I would be at work during the
> pass, I will ask the XYL to change pol every 15 minutes anyway.
>
> Thanks for all who helped me getting the setup working. Really
> appreciated, quite a good learning exercise.
>
> 73
>
>
>
> Jean Marc (3B8DU)
>
>
>
>
> On Jun 9, 2018, at 9:14 PM, Jean Marc Momple <jean.marc.momple@?????.???>
> wrote:
>
> Wei,
>
> Thanks for prompt answer.
>
> OK, got it working fine, but not not sure if uploading to you.
>
> 73
>
> Jean Marc (3B8DU)
>
>
>
> On Jun 9, 2018, at 8:33 PM, ??? <wmc_jx@???.???> wrote:
>
> Hi Jean,
>
> Which recording and flowchart did you use?
>
> for 2MHz recording, you should use frontend_dslwp_replay.grc in
> gr_dslwp/examples.
>
> replay_dslwp_gmsk_250bps_0.5_coherent.grc in dslwp_dev is used for 40kHz
> recording.
>
> Best Regards,
>
> Wei
>
>
>
>
>
> --
> WEI Mingchuan
>
> Research Center of Satellite Technology
> Harbin Institute of Technology
> mobile: +86-189-4501-5242
> e-mail: wmc_jx@???.???? bg2bhc@?????.???
>
>
> At 2018-06-09 23:56:48, "Jean Marc Momple" <jean.marc.momple@?????.???>
wrote:
> >Wei,
> >
> >Thanks for the update.
> >
> >I got everything working today, but could not try decoder with the raw
file, getting error c?RuntimeError: file_meta_source: Could not extract
sample rate.?. Also change my 30m 70cm feeder from RG213 to Heliax 1/2? to
get some more dB and also put a better preamp for some reasons, hopefully it.
> >
> >Could you please send the link for the updated radio info page mentioned
in your mail as cannot find it?
> >
> >Will monitor tomorrow morning and hopefully receive some signal?
> >
> >73
> >
> >Jean Marc (3B8DU)
> >
> >> On Jun 9, 2018, at 1:11 PM, ??? <wmc_jx@???.???> wrote:
> >>
> >> Hi OMs,
> >>
> >>
> >> Just updated the radio info page of DSLWP with some configurations for
successful downlink report. Hope it may help!
> >>
> >>
> >> And the following tests for UHF are planned:
> >>
> >>
> >> 10 Jun 03:40 UTC to 10 Jun 05:40 UTC,
> >> 10 Jun 22:00 UTC to 11 Jun 00:00 UTC,
> >> 11 Jun 06:00 UTC to 11 Jun 08:00 UTC,
> >> 11 Jun 14:00 UTC to 12 Jun 16:00 UTC
> >>
> >>
> >> VY TN & 73!
> >>
> >>
> >> Wei BG2BHC
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> >> --
> >>
> >> WEI Mingchuan
> >>
> >>
> >> Research Center of Satellite Technology
> >> Harbin Institute of Technology
> >> mobile: +86-189-4501-5242
> >> e-mail: wmc_jx@???.??? <wmc_jx@???.???>; bg2bhc@?????.???
> >>
> >>
> >>
> >>
> >>
> >> _______________________________________________
> >> Sent via AMSAT-BB@?????.???. AMSAT-NA makes this open forum available
> >> to all interested persons worldwide without requiring membership.
Opinions expressed
> >> are solely those of the author, and do not reflect the official views
of AMSAT-NA.
> >> Not an AMSAT-NA member? Join now to support the amateur satellite
program!
> >> Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
>
>
>
>
>
>
>
>
------------------------------
Message: 9
Date: Mon, 11 Jun 2018 07:14:42 -0400
From: "Mark L. Hammond" <marklhammond@?????.???>
To: Stephan Greene <ks1g04@?????.???>
Cc: Amsat-bb <amsat-bb@?????.???>
Subject: Re: [amsat-bb] Rotor control with SatPC32ISS
Message-ID:
<CAPRXzyrNyQBP3FZCmyGt76pHM4QRXjgo84Kw9fzUccpCYvjF2w@????.?????.???>
Content-Type: text/plain; charset="UTF-8"
Hi Steve, I think it worked best for me to use the normal SatPC32 to get
rotors and radio all working first. Then switch to the ISS exe. Only
change then is frequency.
Mark N8MH
On Sun, Jun 10, 2018 at 10:04 PM Stephan Greene <ks1g04@?????.???> wrote:
> Long-time SatPC32 user but new to SatPC32ISS. Rig control works fine, but
> I can't get rotor control working in SatPC32ISS. Guessing that SatPC32ISS
> is not launching the rotor control server SatPC32 uses. Suggestions? Does
> SatPC32ISS default to the same config file as SatPC32, or does it default
> to Confguration 1? (I'm using Config II with SatPC32). Have not found
> anything (yet) in the SatPC32 docs.
>
> Thanks, 73 Steve KS1G
> _______________________________________________
> Sent via AMSAT-BB@?????.???. AMSAT-NA makes this open forum available
> to all interested persons worldwide without requiring membership. Opinions
> expressed
> are solely those of the author, and do not reflect the official views of
> AMSAT-NA.
> Not an AMSAT-NA member? Join now to support the amateur satellite program!
> Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
>
--
Mark L. Hammond [N8MH]
------------------------------
Message: 10
Date: Sun, 10 Jun 2018 15:08:28 +0000
From: Kirk P <inservice2him@???????.???>
To: Alfred Watts <awatts44@???????.???>, "amsat-bb@?????.????
<amsat-bb@?????.???>
Subject: Re: [amsat-bb] IC-9100 and SATPC tracking help needed
Message-ID:
<DM5PR13MB09566381D6B6C5FA23A705D1EB790@?????????????.????????.????.???????.??
?>
Content-Type: text/plain; charset="iso-8859-1"
Alfred and others.
TU!
It appears to now be tracking along.
Im not sure why, but it does seem to loose connections at times.
Im using the MicroHam MK2R+ as my interface as I do with all my software.
For some reason this was hard to get communicating. The issue was in the HEX
address.
For my VHF contesting this weekend I was using Writelog and it does not have
IC-9100 as option of all things. So I had to emulate another ICOM for it to
talk. While running SATPC on another screen It was looking for the 9100
address but not getting it. Once I was told how to do the drop down and set
address in SATPC it made sense...simple but overlooked..as it usually is.
Will be good to get back on the birds after about 5 years. New KNWD HT and
ELK and soon Ill have larger ants ready for home qth on az/el rotor now that
EME sation is down for summer.
Again, thanks to all.
Kirk, N0KK EN35
Sent from Outlook<http://aka.ms/weboutlook>
________________________________
From: Alfred Watts <awatts44@???????.???>
Sent: Saturday, June 9, 2018 1:32 PM
To: 'Kirk P'; amsat-bb@?????.???
Subject: RE: [amsat-bb] IC-9100 and SATPC tracking help needed
Kirk
I use SAT32PC Ver. 12.8c on a laptop running Windows 10 and an IC-9100.
I assume your IC-9100 is connected to the PC via a USB cable.
Some things I would check:
Is the device driver for the IC-9100 Installed? Does the IC-9100 talk to
other software such as HRD?
In SAT32PC go to Setup>Radio Setup
Is the Icom button in the Radio 1 panel checked?
Click on Model in the drop-down box. The windows below should say
IC-9100
Click on Baudrate in the drop-down box. The windows below should say
9600
Click on Addresses in the drop-down box. The windows below should
say $7C $7C.
(This are the default addresses in the IC-9100. They can be changed
in the IC-9100 but they must match the addresses set in SAT32PC.)
In the Com Port Window my setup shows Com Port 6 but this will vary
depending on other USB devices. It can also change when change USB devices.
You might try different Com Port numbers.
The Cat Delay box should show 70.
The Satellite Mode box should be checked.
The RTS, DTR and KCT boxes should be unchecked.
At the bottom right corner of the SAT32PC main window does it show Doppl.
Corr: Up/Dwn ?
Then of course the in the upper left of the SAT32PC window there should be
C+ showing when you click on it.
If there is some other setting that you would like to compare e-mail me
directly.
Hope this helps.
73
Al - AF5VH
-----Original Message-----
From: AMSAT-BB <amsat-bb-bounces@?????.???> On Behalf Of Kirk P
Sent: Friday, June 8, 2018 5:22 PM
To: amsat-bb@?????.???
Subject: [amsat-bb] IC-9100 and SATPC tracking help needed
Greetings all.
Trying without success to get my IC-9100 to track with SATPC.
Elmer needed if you've got it going.
Running SatPC32 V.12.8d (2018)
Thank you in advance
Kirk, N0KK
Sent from Outlook<http://aka.ms/weboutlook>
_______________________________________________
Sent via AMSAT-BB@?????.???. AMSAT-NA makes this open forum available to all
interested persons worldwide without requiring membership. Opinions
expressed are solely those of the author, and do not reflect the official
views of AMSAT-NA.
Not an AMSAT-NA member? Join now to support the amateur satellite program!
Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
------------------------------
Message: 11
Date: Mon, 11 Jun 2018 10:25:38 -0400
From: "jeff griffin" <kb2m@????.???>
To: <AMSAT-BB@?????.???>
Cc: 'Richard Lawn' <rjlawn@?????.???>
Subject: Re: [amsat-bb] IC-9100 USB driver issues with WIN10 PRO ver
1803
Message-ID: <037101d40190$11fb7e80$35f27b80$@???>
Content-Type: text/plain; charset="us-ascii"
Problem solved, a comedy of errors. When WIN10 1803 stated to install itself
bit by bit I lost connectivity with my 9100. Not knowing what was going in
on (the formal install of 1803 didn't start yet) First thing I tried was a
different USB cable. What had caused the original problem (WIN10 1803
compatibly issue with the USB drivers used by Icom) turned into two issues,
I added a bad USB cable to the mix. Also the USB driver version 1.30 wasn't
posted to the Icom USA website till this morning, I found a copy at the Icom
UK website. So this morning after some Coffee I back tracked everything I
did, even un installed 1803. After installing the 1.30 drivers, and with the
first USB cable all is working again. Bad cable, and ver 1.20 both are trash
:-)
73 Jeff kb2m
-----Original Message-----
From: jeff griffin [mailto:kb2m@????.????
Sent: Saturday, June 9, 2018 7:48 PM
To: 'jeff griffin'; AMSAT-BB@?????.???
Subject: RE: [amsat-bb] IC-9100 USB driver issues with WIN10 PRO ver 1803
Ok. I will add to this. I had no problem connecting the following USB
devices with no driver upgrades needed to my new laptop. FT-817 with a USB
62c, or a 11 year old K3 with new USB add on connectivity. Plug and play. I
even went back to WIN10 ver 1709 and STILL can't get the 9100 USB to work.
>From the Icom website...
We have an update from our previous posting regarding the compatibility
between the latest version of Windows 10 and Icom Drivers used on the
IC-R8600, IC-7300 and IC-7610. Icom Inc. has confirmed there is an issue and
are in the process of developing an update which they will add to their
global website download page.
In the meantime, we have been given four solutions to fix the issue
temporarily:
Download USB driver 10.1.2 (updated on 14. May 2018) from Silicon
Labs web site.
Download USB driver 6.7.5 (updated on 13. Oct. 2017) from Silicon
Labs web site. This driver is commonly used in OS Windows 7, 8., and Windows
10.
Use the latest version of our USB Driver from the Icom Inc.global
web site (Version is 1.20 for IC-7100/ IC-7200/ IC-7300/ IC-7410/ IC-7600/
IC-7610/ IC-7850/ IC-7851/ IC-9100). As marked driver's information is
6.7.0.
Use PC Windows 10 version 1709.
As soon as we have anymore information, we will post on our website.
Well in my case none of this works. I'm fortunate that I have a backup
laptop that will work for FD. It makes you wonder though, why does Icom
always have all these stupid connectivity issues. I was thinking of selling
my Flex VU5K, and IC-9100 and getting an IC-9700 but now I'm rethinking
that...
73 Jeff kb2m
-----Original Message-----
From: AMSAT-BB [mailto:amsat-bb-bounces@?????.???? On Behalf Of jeff griffin
Sent: Saturday, June 9, 2018 1:11 PM
To: AMSAT-BB@?????.???
Subject: [amsat-bb] IC-9100 USB driver issues with WIN10 PRO ver 1803
I'm having an issue with the USB drivers for my IC-9100 WIN10 1803 setup
that I'm setting up for FD. Odd thing is I have it working on other WIN10
PC's running 1803. Is anyone having the same issue? I'm trying to setup an
HP Spectre PRO x360 G1 i7 laptop. I've tried all the fixes online and none
seem to work.
73 Jeff kb2m
_______________________________________________
------------------------------
Subject: Digest Footer
_______________________________________________
Sent via amsat-bb@?????.???.
AMSAT-NA makes this open forum available to all interested persons worldwide
without requiring membership. Opinions expressed
are solely those of the author, and do not reflect the official views of
AMSAT-NA.
Not an AMSAT member? Join now to support the amateur satellite program!
http://www.amsat.org/mailman/listinfo/amsat-bb
------------------------------
End of AMSAT-BB Digest, Vol 13, Issue 203
*****************************************
Read previous mail | Read next mail
| |
