| |
G8MNY > TECH 16.02.16 10:07l 90 Lines 4134 Bytes #999 (0) @ WW
BID : 60348_GB7CIP
Read: GUEST
Subj: RF Directional Coupler
Path: IW8PGT<IW7BFZ<I3XTY<I0OJJ<GB7CIP
Sent: 160216/0755Z @:GB7CIP.#32.GBR.EURO #:60348 [Caterham Surrey GBR]
From: G8MNY@GB7CIP.#32.GBR.EURO
To : TECH@WW
By G8MNY (Updated Nov 12)
(8 Bit ASCII graphics use code page 437 or 850, Terminal Font)
This is an item used for VHF broadcast transmitter monitoring. It provides low
level calibrated RF sniff point in the aerial coax for Ofcom (UK regulator)
spectrum analyser etc. without turning the Tx off. It is not generally used by
other RF users!
ŚÄÄÄÄÄÄÄÄæ
³Spectrum³
³Analyser³
ĄÄÄÄĀÄÄÄÄŁ
Aerial .ś'ś.
System To Ant To Tx
\³/ ŚÄĮÄÄÄÄÄÄÄĮÄæ ŚÄÄÄæ
ĄÄÄÄÄÄÄ´DirectionalĆÄÄÄ´Tx ³
³ Coupler ³ ĄÄÄÄŁ
ĄÄÄÄÄÄÄÄÄÄÄÄŁ
CIRCUIT
This is quite a straight forward 3 line directional coupler as used in some VHF
SWR bridges, but here all the lines are very accurate 50ź transmission lines.
To Aerial Loss
BNC dB
ŚÄ(o)ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄæ -16 ´ _.-
Aerial ³ ĄÜÜÜÜÜÜÜÜÜÜÜÜÜÜ-50´ Tx -22 ´ _.-'
N Female o)ÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜ(o N Male -28 ´ _.-'
³ _ÜÜÜÜÜÜÜÜÜÜÜÜÜÜ_ ³ -34 ´ _.-'
Ć50 ³ ³ -40 ´ _.-'
ĄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ(o)ÄŁ -46 ´ _.-'
BNC -52 ´-'
To Tx -58 ÅÄÄÄĀÄÄÄĀÄÄÄĀÄÄÄĀÄÄÄĀÄÄÄĀ
12 25 50 100 200 400 800MHz
Such couplers do not have a flat response, they typically have a 6dB per Octave
rise until they are near a resonance or some other losses affect them. Ofcom
said some spectrum analysers have calibration offset parameters that can allow
for this?
A HOMEMADE ONE
Simpler one I made up was from PCB..
To Aerial To Tx
BNC BNC
ŚÄ(o)ÄÄÄÄÄÄÄÄÄ(o)Äæ
Aerial ³ ŽÜÜÜÜÜÜÜÜÜÜÜŻ ³ Tx
N Female o)ÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜ(o N Male
³ ³
ĄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄŁ
The 'N' connectors were bolted to 1" x1" PCB plates, the whole double sided
PCB box soldered up around them & the double sided PCB lines inside that. The
50ohm double sided PCB lines were salvaged from an old VHF SWR detector bridge.
But to make a really good match, it needed solder added to them to get a deep
SWR null on a good load. For this single pick up line design a BNC terminator
plug is used in the unused port.
IN USE
There are accuracy limits to all test gear, here if the transmission system is
not 50ź at the frequency of interest the spectrum analyser result is
meaningless, & this is generally the case off frequency on a resonant aerial!
Actual power measurement is possible provided all the patch lead losses are
known & the match is good.
However the directional coupler does have the ability to show up which RF
mixing faults are internal & external to the Tx ! So nearby corroded metal
joints or other nearby transmitter PAs acting as mixers etc, can easily be
identified as "QRM not in the local Tx". So it is very useful when tracking
down the real cause of QRM.
³ Local² ³ ³
³ Tx² ³ Local ³ Local
³ ² ³ Tx² ³ Tx²
³ ² ³ ² Other ³ ² Other
³ ² Other ³ ² ŽTx ³ ² ŽTx
³ ² Tx ³ ² Ž ³ Mix ² Ž Mix
³ ² Ž ³ ² Ž ³ ³ ² Ž ³
³ Mix ² Ž Mix ³ ² Ž ³ ³ ² Ž ³
³ ³ ² Ž ³ ³ Mix ² Ž Mix ³ ³ ² Ž ³
ĄÄÄĮÄÄÄÄÄÄÄÄÄÄÄÄÄĮÄÄÄÄ ĄÄÄĮÄÄÄÄÄÄÄÄÄÄÄÄÄĮÄÄÄÄ ĄÄÄĮÄÄÄÄÄÄÄÄÄÄÄÄÄĮÄÄÄÄ
Tx Port Spectrum Aerial Port Spectrum Aerial Port Spectrum
Showing Local Tx Mixing Showing External Mixing
(mix less than Tx Port) (mix more than Tx Port)
Why Don't U send an interesting bul?
73 de John G8MNY @ GB7CIP
Read previous mail | Read next mail
| |
