OpenBCM V1.07b12 (Linux)

Packet Radio Mailbox

IW8PGT

[Mendicino(CS)-Italy]

 Login: GUEST





  
G8MNY  > TECH     30.09.18 09:44l 110 Lines 4875 Bytes #999 (0) @ WW
BID : 40112_GB7CIP
Read: GUEST
Subj: Realistic Pro2005/6 mods
Path: IW8PGT<CX2SA<SV1CMG<GB7COW<ZS0MEE<N9PMO<I0OJJ<GB7CIP
Sent: 180930/0736Z @:GB7CIP.#32.GBR.EURO #:40112 [Caterham Surrey GBR]

>From g8mny%gb7cip.#32.gbr.euro@i0ojj.ampr.org Sun Sep 30 09:37:14 2018
Received: from i0ojj.ampr.org by i0ojj.ampr.org (JNOS2.0k.3b) with SMTP
	id AA52793 ; Sun, 30 Sep 2018 09:37:14 +0200
Message-Id: <40112_GB7CIP@gb7cip.bbs>
>From: g8mny@gb7cip.#32.gbr.euro
X-JNOS-User-Port: Telnet   (gb7cip @ 82.70.39.222)  -> Sending message

From: G8MNY@GB7CIP.#32.GBR.EURO
To  : TECH@WW

By G8MNY                                (New Oct 18)
(8 Bit ASCII graphics use code page 437 or 850, Terminal Font)

Here is a collection of mods I have done to these identical scanners, so they
can be used as unmanned single channel broadcast link Rx, but still leave full
functionality as a scanner if needed.
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ ±±±±±±±±±±±±±   ±±±±±±±±±±±±± ³
³³ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ ³ ÚÄÄ¿ ÚÄÄ¿ ÚÄÄ¿ ÚÄÄ¿ ÚÄÄ¿ ÚÄÄ¿ ³
³³ ³     1 2 3 4 5 6 7 8 9 10   ³ ³ ³ ÀÄÄÙ ÀÄÄÙ ÀÄÄÙ ÀÄÄÙ ÀÄÄÙ ÀÄÄÙ ³
³³ ³     001ch  1 4 5 .5 0 0 MHz³ ³ ³ ÚÄÄ¿ ÚÄÄ¿ ÚÄÄ¿ ÚÄÄ¿ ÚÄÄ¿ ÚÄÄ¿ ³
³³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ³ ³ ÀÄÄÙ ÀÄÄÙ ÀÄÄÙ ÀÄÄÙ ÀÄÄÙ ÀÄÄÙ ³
³ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ³ ÚÄÄ¿ ÚÄÄ¿ ÚÄÄ¿ ÚÄÄ¿ ÚÄÄ¿ ÚÄÄ¿ ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ÀÄÄÙ ÀÄÄÙ ÀÄÄÙ ÀÄÄÙ ÀÄÄÙ ÀÄÄÙ ³
³        __      __      400 Channel³ ÚÄÄ¿ ÚÄÄ¿ ÚÄÄ¿ ÚÄÄ¿ ÚÄÄ¿ ÚÄÄ¿ ³
³       /  \    /  \      .  Pro2005³ ÀÄÄÙ ÀÄÄÙ ÀÄÄÙ ÀÄÄÙ ÀÄÄÙ ÀÄÄÙ ³
³      (    )  (    )   ÚÄÄ¿   ÚÄÄ¿ ³ ÚÄÄ¿ ÚÄÄ¿ ÚÄÄ¿ ÚÄÄ¿ ÚÄÄ¿      ³
³ (o)   \__/    \__/    ÀÄÄÙ   ÀÄÄÙ ³ ÀÄÄÙ ÀÄÄÙ ÀÄÄÙ ÀÄÄÙ ÀÄÄÙ      ³
ÀÄÄÂÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÂÄÄÙ
    ~~~                                                       ~~~
A/ Mod to give Squelch line & WBFM HiFi audio outputs. (Tape out is not HiFi!)

1. Drill 2 holes for 2 additional bolt Phono in sockets, located above the DC
   in connector.
2. Place PNP emitter follower above IC6.

   IC6-14 +8VÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
              330                                       ³
               ³      +10u                 Squelch     1K
               ÃÄÄ2K7ÄÄ´ÃÄÂÄÄÄÂÄÄÄÄÂÄÄÄÄ¿  Diode        ³
               ³          ³   ³10n ³    ³   D46Ä¿       ÃÄÄÄo)SQ
             ³/e         === ===   ³     \³     ³     ³/     ³Phono
   IC6-1 ÄÄÄÄ´  BC212  10nÀÄÂÄÙ    ³ BC337ÃÄ10KÄÁÄ10KÄ´BC337 ³
             ³\            820   AFo)   e/³           ³\e    ³
               ³        EQ R³  Phono³   ³ Mute   Squelch³    ³
   IC6-7 0VÄÄÄÄÙ            ÀÄÄÄÄÄÄÄÁÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÙ

3. Add 50uS de-emphasis components 2x 10n, EQ R, series 2K7, 10uF, 100K, & Mute
   NPN on to the AF phono socket.
4. Add squelch NPN to SQ phono socket. Connect both base 10Ks to top of the
   nearby diode D46.
5. Test functionality, SQ O/P is +8V on good WBFM, & AF is good, & is muted
   with the internal comms squelch. No Op on other modes.


B/ Mod to improve Squelch control action. (all one end & huge hystersis!)

1. Improve zero end action. Put a 10K from Squelch control slider to pot
   ground.
        ÚÄÄÄÄÄÄÄ                ÚÄ220ÄÄ¿
   Squelch                      ³      ³
   Control<ÄÄÂÄÄ              RÄÅÄR158ÄÁÄIC2-12
       Pot  10K                +³  4k7
        ÀÄÄÄÄÁÄÄ               ===
                                ³C185

2. Reduce hysterisis by reducingstfunction. Weak signal squelch threshold more easily set, & snap on &
   off action much closer in level.


C/ Mod to set manual mode not "scan mode" on power up. (Default is scan!)
 
1. Connect wire from +5V on LM7805 regulator to a 100K & a 1N4148 diode near
   the front panel upper PCB connector keyboard matrix plug.

   LM7805 +5VÄÄÄÂÄ´<ÃÄÄ's base & push emitter & collector into 5 & 7, hot glue.
4. Wire up 3 components to the +ve cap lead.
5. Test functionality. On power up the PNP conducts for ~200mS & check the
   scanner always goes into manual mode.


D/ Mod to improve PSU, & RFI. (reduce bad mains crashing?)
 
1. Add 2 small ferrite rings (FB) on 14V AC PCB input leads from transformer.

     ÄÄÄÄ¿  ÚÄÄFBÄÄÂÄÄÂÄ´>ÃÄÄÂÄRÄÂÄÄÄÄÂÄLM7805ÄÄ+5V
         )³³(      ³  ³      ³   ³ 4m7³+  ³
         )³³(      ³  ÀÄ´<ÿ ³   ³   ===  ³
   MAINS )³³( .1u ===      ³ ³  +³    ÀÄÄ         )³³(      ³  ÚÄ´³(       ³     m2³
     ÄÄÄÄÙ  ÀÄÄFBÄÄÁÄÄÁÄ´ÁÄÄÄÄÄÁrode
my community stati'plswithout the cost of 2 bespoke dedicated Rx.

My choice of 2x 50kHz identical mono links channels, for the station's uplink,
are not only cheaper to rent than a single 200kHz wide stereo link channel, but
are 2x more reliable (surviving on 1), & can give about 20dB better signal to
noise than a stereo link can do!

Other precautions taken were, a series a fed widistant shared dband& a backup AF source, is controlled from the 2 Squelch lines
.

They have given fairly trouble free hifi broadcast  Principles" & "SUSY  +5
more".


Why Don't U send an interesting bul?

73 De John, G8MNY @ GB7CIP




Read previous mail | Read next mail


 12.05.2024 06:06:10lGo back Go up